200-301試験無料問題集（990題）「Cisco Certified Network Associate 認定」

出題：1

What is an expected outcome when network management automation is deployed?

A. Software upgrades are performed from a central controller

B. Complexity increases when new device configurations are added

C. Custom applications are needed to configure network devices

D. A distributed management plane must be used.

正解：A 解答を投票する

出題：2

Refer to the exhibit. After the configuration is applied, the two routers fail to establish an OSPF neighbor relationship. what is the reason for the problem?

A. Router2 is using the default hello timer.

B. The OSPF router IDs are mismatched.

C. The network statement on Router1 is misconfigured.

D. The OSPF process IDs are mismatched.

正解：A 解答を投票する

出題：3

Which IPsec encryption mode is appropriate when the destination of a packet differs from the security termination point?

A. main

B. tunnel

C. transport

D. aggressive

正解：C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：4

Drag and drop the characteristic from the left onto the IPv6 address type on the right.

正解：

Explanation:

出題：5

Which switch technology establishes a network connection immediately when it is plugged in?

A. UplinkFast

B. PortFast

C. BackboneFast

D. BPDU guard

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：6

What causes a port to be placed in the err-disabled state?

A. latency

B. shutdown command issued on the port

C. nothing plugged into the port

D. port security violation

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：7

What is the effect when loopback interfaces and the configured router ID are absent during the OSPF Process configuration?

A. The router ID 0.0.0.0 is selected and placed in the OSPF process.

B. The highest up/up physical interface IP address is selected as the router ID.

C. No router ID is set, and the OSPF protocol does not run.

D. The lowest IP address is incremented by 1 and selected as the router ID.

正解：B 解答を投票する

出題：8

Refer to the exhibit.

If OSPF is running on this network, how does Router 2 handle traffic from Site B to 10.10.13/25 at Site A?

A. It sends packets out of interface Fa0/1 only.

B. It sends packets out of interface Fa0/2 only.

C. It cannot send packets to 10.10.13 128/25

D. It load-balances traffic out of Fa0/1 and Fa0/2

正解：C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：9

Refer to the exhibit. An engineer must translate the PC1 IP address to 10.199.77.100 and permit PC1 to ping the loopback 0 on router R2. What command set must be used?

A.

B.

C.

D.

正解：D 解答を投票する

出題：10

Refer to the exhibit.

Routers R1 and R2 are configured with RIP as the dynamic routing protocol. A network engineer must configure R1 with a floating static route to serve as a backup route to network 192.168.23. Which command must the engineer configure on R1?

A. ip route 192.168.23.0 255.255.255.0 192.168.13.3

B. ip route 192.168.23.0 255.255.255.255 192.168.13.3 121

C. ip route 192.168.23.0 255.255.255.0 192.168.13.3 121

D. ip route 192.168.23.0 255.255.255.0 192.168.13.3 100

正解：C 解答を投票する

出題：11

Refer to the exhibit.
PC A and the file server. Which commend must be configured on switch A to prevent interruption of other communications?

A. switchport trunk allowed vlan none

B. switch port trunk allowed vlan 12

C. switchport trunk allowed vlan add 13

D. switch port trunk allowed vlan remove 10-11

正解：C 解答を投票する

出題：12

Refer to the exhibit.

An engineer is asked to insert the new VLAN into the existing trunk without modifying anything previously configured Which command accomplishes this task?

A. switchport trunk allowed vlan 100-104

B. switchport trunk allowed vlan all

C. switchport trunk allowed vlan add 104

D. switchport trunk allowed vlan 104

正解：D 解答を投票する

出題：13

An engineer is configuring switch SW1 to act an NTP server when all upstream NTP server connectivity fails.
Which configuration must be used?

A.