300-610試験無料問題集「Cisco Designing Cisco Data Center Infrastructure 認定」
Refer to the exhibit. A high-availability setup for iSCSI is designed with the host running iSCSI multipath software. Each IP storage port on the MDS switch exports the same two Fibre Channel target ports with different iSCSI target names.
In this design, how many iSCSI sessions are created from the host so that recovery occurs if any component fails?
In this design, how many iSCSI sessions are created from the host so that recovery occurs if any component fails?
正解：B
解答を投票する
解説: (GoShiken メンバーにのみ表示されます)
A network consultant evaluates the Ethernet Adapter Policy configuration to be applied to the Cisco UCS blade servers. The policy must minimize latency and increase throughput for sensitive applications. The solution must increase the CPU data cache hit rate to meet these requirements Which policy is required?
正解：B
解答を投票する
A company has added a new FCoE storage array to increase the performance of datastore access for end users. This storage array is directly connected to the Cisco Nexus 5672UP switches using four 10G port-channel interfaces. After deployment, the end users fail to access the datastore compared to the older solution. A network engineer verified the port-channel interface and finds that the congestion occurs when PFC frames are generated at the FCoE ingress interface. Which action must be taken to resolve the congestion issue?
正解：B
解答を投票する
Refer to the exhibit. Server 1 fails to connect to the storage array over the Storage Area Network (SAN) of the Cisco NDS 9000 Series Switch.
The requirements are to redesign the storage network and keep these considerations in mind:
The traffic from each of the server must be redundant and isolated.
The design must tolerate hardware and software failures and upgrades of SAN fabric devices.
Which action must be taken to meet these requirements?
The requirements are to redesign the storage network and keep these considerations in mind:
The traffic from each of the server must be redundant and isolated.
The design must tolerate hardware and software failures and upgrades of SAN fabric devices.
Which action must be taken to meet these requirements?
正解：A
解答を投票する
An engineer manages a multi-organization Cisco UCS fabric and requires a solution to streamline the daily operational tasks of creating service profile templates. The operations team is unfamiliar with programming languages and must have a solution that is written in an easy-to-read and declarative manner. The operations team also requires the tool to be flexible enough to support the creation of custom modules. The development team is familiar with the Python programming language and can develop these custom modules for the operations team.
Which tool meets these requirements?
Which tool meets these requirements?
正解：A
解答を投票する
A Cisco engineer is preparing a service profile template for a design, which consists of 20 x UCS B200M6 blade servers, 2 x UCS 6454 Fabric Interconnect in End Host Mode, and 3 x UCS 5108 server chassis with 2408 Fabric Extenders. The blade servers are equipped with VIC 1480 adapters. The engineer does not configure a vNIC/vHBA placement policy in the service profile and the vNICs and vHBAs are assigned to the vCon in a particular order. What is the mapping scheme in which Cisco UCS assigns the vCons based on the type of server and the selected virtual slot?
正解：D
解答を投票する
A network architect proposes a distinct Fibre Channel fabric to be used for a Cisco UCS blade server that hosts critical applications.
Which action should be implemented for the Fibre Channel traffic from the vHBA of this server to pass through the I/O Module in the Cisco UCS chassis to a specified uplink Fibre Channel port?
Which action should be implemented for the Fibre Channel traffic from the vHBA of this server to pass through the I/O Module in the Cisco UCS chassis to a specified uplink Fibre Channel port?
正解：B
解答を投票する
解説: (GoShiken メンバーにのみ表示されます)
An engineer is installing a Cisco Nexus 7000 Series Switch with F2-Series I/O Module. The company's strict security policy requires that the port be in-band. The engineer must also keep these considerations in mind:
- The customer's security requirements mandate the use of a secure
management mechanism that supports authentication and encryption.
- The port should support management over IP.
Which port type must be used to meet these requirements?
- The customer's security requirements mandate the use of a secure
management mechanism that supports authentication and encryption.
- The port should support management over IP.
Which port type must be used to meet these requirements?
正解：D
解答を投票する
Drag and Drop Question
Refer to the exhibit. An engineer must deploy a SAN that meets these criteria:
- The upstream director switch must be configured to minimize the
number of issued domain IDs
- The access switch must aggregate multiple locally connected ports not a single uplink that shares the same domain ID as the upstream switch.
Drag and drop the port types from the right onto the boxes on the left to create a SAN topology that meets these requirements. Not all port types are used Port types are used more than once.
Refer to the exhibit. An engineer must deploy a SAN that meets these criteria:
- The upstream director switch must be configured to minimize the
number of issued domain IDs
- The access switch must aggregate multiple locally connected ports not a single uplink that shares the same domain ID as the upstream switch.
Drag and drop the port types from the right onto the boxes on the left to create a SAN topology that meets these requirements. Not all port types are used Port types are used more than once.
正解：
