600-512試験無料問題集（60題）「Cisco Implementing with Cisco Network Programmability for ACI (NPENGACI) 認定」

出題：1

Which three types of interfaces are supported to connect a border leaf switch to an external router? (Choose three.)

A. Layer 3 interface

B. SVI

C. bridge domain interface

D. tenant interface

E. Layer 3 subinterface

F. EPG interface

G. Layer 2 interface

正解：A,B,E 解答を投票する

出題：2

You must create a bridge domain that has one subnet. The supported IP address range should be
10.12.10.0 through 10.12.11.254. The default gateway should be 10.12.11.100. Which configuration is correct?

A. <fvBD name="solarBD1"> <fvRsCtx tnFvCtxName="solarctx1" /> <fvSubnet ip="10.12.11.100/23"> <fvRsBDSubnetToProfile tnL3extOutName="rout1" tnRtctrlProfileName="profExport" /> </fvSubnet></fvBD>

B. <fvBD name="solarBD1"> <fvRsCtx tnFvCtxName="solarctx1" /> <fvSubnet ip="10.12.10.0/24"> <fvRsBDSubnetToProfile tnL3extOutName="rout1" tnRtctrlProfileName="profExport" /> </fvSubnet> <fvSubnet ip="10.12.11.100/24"> <fvRsBDSubnetToProfile tnL3extOutName="rout1" tnRtctrlProfileName="profExport"/> </fvSubnet></fvBD>

C. <fvBD name="solarBD1"> <fvRsCtx tnFvCtxName="solarctx1" /> <fvSubnet ip="10.12.10.0/23" gateway=10.12.11.100> <fvRsBDSubnetToProfile tnL3extOutName="rout1" tnRtctrlProfileName="profExport" /> </fvSubnet></fvBD>

D. <fvBD name="solarBD1"> <fvRsCtx tnFvCtxName="solarctx1" /> <fvSubnet ip="10.12.10.0/23"> <fvRsBDSubnetToProfile tnL3extOutName="rout1" tnRtctrlProfileName="profExport" /> </fvSubnet> <fvSubnet ip="10.12.11.100/23"> <fvRsBDSubnetToProfile tnL3extOutName="rout1" tnRtctrlProfileName="profExport"/> </fvSubnet></fvBD>

正解：A 解答を投票する

出題：3

Which two characteristics describe a VXLAN encapsulation? (Choose two.)

A. uses 24-bit virtual network ID and TCP port 179

B. uses 42-bit virtual network ID and TCP port 179

C. uses 24-bit virtual network ID and UDP port 8472

D. adds an 8-byte header, most of which is reserved with the exception of the 3-byte instance ID

E. uses 42-bit virtual network ID and UDP port 8472

正解：C,D 解答を投票する

出題：4

Which source can be specified as a SPAN source at the tenant level?

A. EPG

B. VLAN

C. VXLAN

D. port

E. EP

正解：A 解答を投票する

出題：5

When you are logged into the Cisco APIC console as the "admin" user, which command displays all nodes that are registered to the fabric?

A. acishow nodelist

B. acidiag fnvread

C. acidiag avread

D. acishow fabric

正解：B 解答を投票する

出題：6

Which command in the CLI of a leaf displays the status of vPC that has been enabeld on this switch?

A. show explicit-protection-group

B. show vpc-domain

C. show protection domain

D. show vpc

正解：D 解答を投票する

600-512試験無料問題集「Cisco Implementing with Cisco Network Programmability for ACI (NPENGACI) 認定」