D-PSC-MN-01試験無料問題集（150題）「EMC Dell PowerScale Maintenance 認定」

出題：1

A platform engineer is connecting a new Dell PowerScale F600 node to the frontend switch in an existing cluster with legacy nodes.
How should the network cables be connected?

A. From the PCIe slot 3 to the frontend Ethernet switch

B. From the PCIe slot 1 to the frontend Ethernet switch

C. From the PCIe slot 3 to the frontend InfiniBand switch

D. From the PCIe slot 1 to the frontend InfiniBand switch

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：2

An organization has a cluster of F800 nodes running OneFS version 9.0. A platform engineer is planning to add a new node pool of F600 nodes. While unpacking the first F600 node, the IT manager notices two of the ten drive bays are empty and asks the platform engineer about it.
How should the platform engineer respond?

A. Sales order shows 8-drive nodes instead of 10-drive nodes

B. Two additional drives are packaged separately

C. Two empty drive bays are dedicated for L3 cache

D. F600 nodes only use 8 of the 10 drive bays

正解：D 解答を投票する

出題：3

Exhibit.

A platform engineer has connected power cables to a Dell PowerScale Gen6 node.
What does the status indicator indicate?

A. Not functioning

B. On and healthy

C. Mismatch of voltage or component firmware

D. Cold and redundant

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：4

Which tool is essential for completing a PowerScale cluster configuration that is compliant with specific industry standards?

A. A storage capacity planning tool

B. A compliance benchmarking tool

C. A hardware compatibility checker

D. A network configuration utility

正解：B 解答を投票する

出題：5

Dell EMC Technical Support has requested a part to be sent directly back to Dell Logistics to be studied.
Which process or document needs to be completed prior to sending the part back?

A. CDMR

B. WWFA

C. WWF

D. DMR

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：6

What is the recommended way to install a Dell PowerScale Gen 6 compute module in a chassis?

A. Loosen the thumbscrew on the release lever then slide the compute module into the chassis.

B. Slide the release lever to the right and guide the node into the chassis.

C. Close the module lever and slide the module into the chassis until it clicks.

D. Support the node with both hands and slide it into the node bay.

正解：D 解答を投票する

出題：7

What must be replaced at the same time the backup battery is replaced?

A. M.2 card and backup battery

B. Both NIC cards

C. Riser card

正解：A 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：8

What is a critical consideration when replacing a network card, a key CRU, in a PowerScale node?

A. The card is hot-swappable.

B. The node's operating system is reinstalled.

C. The new card has identical physical dimensions.

D. The card is compatible with the node's hardware version.

正解：D 解答を投票する

出題：9

During the process of adding a node to a PowerScale cluster, what does smartfailing a node entail?

A. Marking a node as failed so it can be safely removed and replaced

B. Temporarily isolating a node for performance testing

C. Increasing the priority of a node in the resource allocation

D. Forcibly removing a node from the cluster

正解：A 解答を投票する

出題：10

A platform engineer has added an F200 node to a Dell EMC PowerScale cluster. The cluster now has five F200 nodes.
Before leaving the site, what action must the engineer perform?

A. Verify the node LNN is set to 1

B. Reboot the node and wait for a green status

C. SmartFail the node and rejoin the cluster

D. Ensure the install base record is updated

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

D-PSC-MN-01試験無料問題集「EMC Dell PowerScale Maintenance 認定」