DES-4421試験無料問題集（55題）「EMC Specialist - Implementation Engineer, PowerEdge MX Modular 認定」

出題：1

A technician replaces a failed Management Module in an MX7000 chassis group. After the technician leaves the site, the administrator reports that the lead chassis is no longer able to communicate with its members.
How can OME-M be used to confirm the cabling configuration?

A. View the health status of the lead Chassis Management ports

B. View the health status of the lead Chassis Management Module

C. View the I/O module topology map from the lead chassis

D. View the topology map from the Group Lead

正解：A 解答を投票する

出題：2

A company receives their first MX7000 chassis. They connect all the provided power supply cables into two different PDUs on different power grids for redundancy. Each of the six power supplies is cabled and has green LEDs. One Management Module is present along with all system fans. Grid redundancy is configured as the power redundancy mode. The chassis is fully populated with six compute sleds and one IOM but only two of the six sleds will power on.
What is the possible reason for this issue?

A. Power supply unit redundancy policy was not used.

B. An additional IOM is required to power on and manage the remaining sleds.

C. Two Management Modules are required to power on the populated chassis.

D. Mixed high line and low line AC inputs in the same chassis is not supported.

正解：A 解答を投票する

出題：3

Where in the OME-M Web interface can the Chassis Deployment Wizard be found?

A. Home > Settings > Chassis Deployment Wizard

B. Home > Configure > Initial Configuration

C. Configuration > Deploy > Chassis Deployment Wizard

D. Hardware > Initial Configuration

正解：B 解答を投票する

出題：4

An MX7000 administrator has been tasked to create a Scalable Fabric Architecture on a 3 chassis setup using Fabric B.
Which IOM configuration is recommended?

A. Chassis 1 - Slot B1: MX9116n; Slot B2: MX7116nChassis 2 - Slot B1: MX7116n; Slot B2:
MX9116nChassis 3 - Slot B1: MX7116n; Slot B2: MX7116n

B. Chassis 1 - Slot B1: MX7116n; Slot B2: MX7116nChassis 2 - Slot B1: MX7116n; Slot B2:
MX7116nChassis 3 - Slot B1: MX9116n; Slot B2: MX9116n

C. Chassis 1 - Slot B1: MX9116n; Slot B2: MX9116nChassis 2 - Slot B1: MX5108n; Slot B2:
MX5108nChassis 3 - Slot B1: MX5108n; Slot B2: MX5108n

D. Chassis 1 - Slot B1: MX9116n; Slot B2: MX5108nChassis 2 - Slot B1: MX5108n; Slot B2:
MX9116nChassis 3 - Slot B1: MX5108n; Slot B2: MX5108n

正解：C 解答を投票する

出題：5

What item is used to refer to a daisy-chained configuration of a multiple MX7000 chassis environment?

A. Physical group

B. Wired group

C. Identity group

D. Chassis group

正解：B 解答を投票する

出題：6

Which I/O module(s) supports Full Switch and SmartFabric operating modes?

A. MX9116n and MX5108n

B. MX9116n only

C. MX9116 and MX7116n

D. MX5108 and MX5016s

正解：A 解答を投票する

DES-4421試験無料問題集「EMC Specialist - Implementation Engineer, PowerEdge MX Modular 認定」