HP0-Y49試験無料問題集（102題）「HP ATP FlexNetwork Solutions 認定」

出題：1

Refer to the exhibit.
Exhibit: Network topology and configuration Originally, all four switches had the same region configuration. VLAN 14 was added to Switch_D and then mapped to instance 2. How does this affect the MSTP topology?

A. All connectivity is lost, both uplinks are blocked on Switch_D

B. Load sharing is lost, one of the uplinks is blocked for all traffic on Switch_C and Switch_D

C. Load sharing is lost, one of the uplinks is blocked for all traffic on Switch_D

D. A layer 2 loop exists and will cause sporadic connectivity issues

正解：A 解答を投票する

出題：2

A network administrator attempts to create a loopback interface on an HP Comware switch, and it fails. These are the commands the network administrator issues to do this.
[Comware] interface loopback 2
[Comware-Loopback2] ip address 172.18.20.1 255.255.255.0
What is the problem with the proposed configuration/

A. Loopback IP addresses must be in the 10.x.x.x subnet ranges

B. Only one loopback is supported in Comware Loopback2 cannot be configured

C. Loopback interface on Comware must use 32-bit marks

D. Only HP ProVision switches support loopback interface

正解：C 解答を投票する

出題：3

When LLDP is enabled, which value is presented by default as the LLDP Chassis ID on both ProVision and Comware switches?

A. IP address

B. System Name

C. MAC address

D. Router ID

正解：C 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：4

Which wireless technology is limited to operate in a frequency range with only three non-overlapping channels?

A. 802.1ad

B. 802.1x

C. 802.1a

D. 802.11g

正解：D 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：5

When configuring a static route, what is used as the next hop address?

A. IP of the default gateway in the destination subnet

B. IP interface of the neighboring router, which receives traffic as an intermediary

C. Lowest IP address of the neighboring router

D. IP of the local egress interface forwarding traffic towards its destination

正解：B 解答を投票する

出題：6

Which HP ProVision switch command defines 10.1.1.1 as a syslog server?

A. Logserver 10.1.1.1

B. Logging 10.1.1.1

C. Syslog 10.1.1.1

D. Info-center 10.1.1.1

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：7

Refer to the exhibit. Exhibit: Network topology

A company has implemented a switched network based on the RSTP spanning tree protocol. Assume the following:
-All switches have the same priority -All ports have the same cost -All ports have the same priority
Based on this information, which answer is correct?

A. Port 1 on SwitchD is a root port.

B. Port 3 on SwitchC is a designated port.

C. Port 2 on SwitchC is a designated port.

D. Port 1 on SwitchB is a discarding port.

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

出題：8

A customer is implementing a network using HP ProVision switches. Which default setting applies to the ProVision switches?

A. A static IP address is assigned to VLAN 1

B. Routing is enabled

C. All Ports are disabled

D. SSH is enabled

正解：D 解答を投票する

出題：9

Which type of access is considered an In-band management connection?

A. Dial-up to an auxiliary port

B. Serial connection to Console port

C. SSH from a desktop to the device

D. Telnet to an HP iLO management port

正解：C 解答を投票する

出題：10

A customer has an HP ProVision switch capable of Layer 3 forwarding: however, Layer 3 forwarding is disabled. The switch has an IP address in the management VLAN, where the default gateway is 10.1.1.1, which ProVision command should the network administrator use so the ProVision switch can access the Intelligent Management Center (IMC) server in a different VLAN?

A. IP route 0.0.0.0 255.255.255.255 10.1.1.1

B. IP route 0.0.0.0.0.0.0.0 10.1.1.1

C. IP default-gateway 10.1.1.1

D. Default-route 10.1.1.1

正解：B 解答を投票する

解説: (GoShiken メンバーにのみ表示されます)

HP0-Y49試験無料問題集「HP ATP FlexNetwork Solutions 認定」