H12-811試験無料問題集（732題）「Huawei HCIA-Datacom V1.0 認定」

出題：1

IP route--statiC.10.0.12.0255.255.255.0192.168.1.1 About this command description is correct ()

A. If the router learns a router with the same destination network as this route through other protocols, the router will prefer this route

B. This command configures a route to the 10.0.12.0 network

C. This command configures a route to the 192.168.1.1 network

D. The priority of this route is 100

正解：B 解答を投票する

出題：2

When the LCP phase of PPP is negotiated, the content of the negotiation includes ()*

A. IP address

B. MRU

C. Authentication protocol

D. Magic word

正解：B,C,D 解答を投票する

出題：3

In which working state of the port in the STP protocol can it be changed to the Forwarding state without going through other states? ()

A. Listening

B. Blocking

C. Learning

D. Disabled

正解：C 解答を投票する

出題：4

The election of the root switch in STP only compares the priority of the switch, while in RSTP, the priority of the switch is compared with the MAC address at the same time. ()

A. True

B. False

正解：B 解答を投票する

出題：5

Which of the following protocols does the RA. message used by IPv6 stateless autoconfiguration belong to? ()

A. ICMPv6

B. IGMPv6

C. TCPv6

D. UDPv6

正解：A 解答を投票する

出題：6

Which of the following commands can be used to query the configuration information of the device's 0SPF protocol? ()*

A. Enter the command "display t in the OsPF protocol view.
his\
,.:
,.:

B. dis ip routing-table

正解：A,B 解答を投票する

出題：7

To ensure that the same data stream is forwarded on the same physical link, which load sharing method does Eth Trunk use?

A. Packet-based load sharing

B. Load sharing based on application layer information

C. Load sharing based on data packet inbound interface

D. Flow-based load sharing

正解：D 解答を投票する

出題：8

As shown in the figure below, the network. All switches enable the STP protocol. Disable SWA's G0/0/2 port to configure the BPDU sending function. SWC's G0/0/1 reconverges to become the root port. Which of the following statements is correct about this process? () (Multiple Choice Questions)

A. SWB sends configuration BPDU with TCA set to SWC

B. SWB forwards TCN BPDU to SWA

C. SWC sends TCN BPDU to SWB

D. SWA sends configuration BPDU with TC set

正解：A,B,C 解答を投票する

出題：9

Now you need to implement a Python automation script Telnet to the device to view the running configuration of the device. What is wrong with the following statement? ()

A. Use telnet.Telnet (host) to connect to the Telnet server.

B. Telnet.close() is used every time a command is entered, and the function is that the user waits for the switch to return information. ?

C. TelnetliB. can achieve this function.

D. You can use telnet.write (b\) to input the command to view the current configuration of the device.

正解：B 解答を投票する

出題：10

The configuration information of a certain port of the switch is shown in the figure. Then, when the data frame of which VLAN is sent by this port, it carries the VLAN TAG? ()interface GigabitEtherneto/0/1 port hybriD.taggeD.vlan 2 to 3 100 port hybriD. untaggeD. vlan 4 6#

A. 2, 3, 100

B. 2.3, 4, 6, 100

C. 1, 2, 3, 4.6, 100

D. 1, 2.3, 100

正解：A 解答を投票する

出題：11

As shown in the figure below. Which port of the following switches will be blocked? () (Single- choice question)

A. SWC's G0/0/2

B. G0/0/3 of SWB

C. SWA's G0/0/3

D. SWC's G0/0/1

正解：D 解答を投票する

出題：12

There are hosts in a private network that need to access 1nternet. In order to achieve this requirement, which of the following configurations should be done by the administrator on the edge router of the network? ()*

A. Default route

B. STP

C. DHCP

D. NAT

正解：A,D 解答を投票する

出題：13

Switch stacking supports more than two devices, and multiple switches can be grouped into a logical device through stacking. ()

A. True

B. False

正解：A 解答を投票する

出題：14

On Huawei devices, if you use aaA authentication to authorize. When the remote server does not respond, you can authorize from the network device side ()

A. True

B. False

正解：A 解答を投票する

出題：15

The NAT configuration is as follows, which IP can be converted when accessing the public network (RTA) acl2000 (RTA-acl-basic-2000) rule5 permit source 192.168.1.00.0.0.255 RTA-acl- basic-2000) rule 10 deny source 192.168. 1.30 (RTA-acl-basic-2000) quit RTA) interface serial1/0/0 (RTA-Serial1/0/0) nat outbounD.2000*

A. 192.168.2.1

B. 192.168.1.3

C. 192.168.1.2

D. 192.168.1.1

正解：B,C,D 解答を投票する

H12-811試験無料問題集「Huawei HCIA-Datacom V1.0 認定」