H12-931-ENU試験無料問題集（320題）「Huawei Certified Internetwork Expert-Transmission 認定」

出題：1

Preparation conditions for single-site commissioning of transmission equipment include (multiple choices)

A. Does the power supply have

B. Whether the related optical fiber and cable are installed in place

C. Make sure that the network management program installed on the laptop is normal

D. Whether the hardware installation is qualified

正解：A,B,C,D 解答を投票する

出題：2

When the EX2 board of the PTN equipment is connected to the STM-64 port, how should the working mode of the interface be set?

A. Self-negotiation

B. Adaptive

C. LAN

D. Cannot be docked

E. WAN

正解：E 解答を投票する

出題：3

Discrete services are cross-connections with no path formed on the network management. Since no path is formed, it is a junk service and can be deleted directly.

A. FALSE

B. TRUE

正解：A 解答を投票する

出題：4

Commonly used methods to improve the utilization of network resources are (multiple choice)

A. Add a dot on the ring

B. Remove the MSP ring into a smaller ring

C. Change the protection method, such as changing SNCP to MSP

D. Change the protection method, such as changing MSP to SNCP

正解：B,C 解答を投票する

出題：5

The interface board N1SF64 of OSN 7500 and the A1SF64 of OptiX 10G (Metro 5000) support different protocols, so they cannot be connected.

A. FALSE

B. TRUE

正解：B 解答を投票する

出題：6

MSTP equipment TDM plane can support 1588V2

A. FALSE

B. TRUE

正解：A 解答を投票する

出題：7

The following dispersions exist in single-mode fibers: material dispersion, waveguide dispersion, polarization mode dispersion, and modal dispersion.

A. FALSE

B. TRUE

正解：A 解答を投票する

出題：8

The insertion loss of the 40 sub-wavelength channels of D40 is 6dB, regardless of the influence of noise, when the signal is full-wave, the IN port optical power of D40 is X dBm. If the optical power of the IN port is reduced by 1dB, The measured value is () dBm. (Assuming that the optical power of each channel is balanced, lg40=1.6)

A. (X-5)

B. (X-22)

C. (X-23)

D. (X-6)

正解：C 解答を投票する

出題：9

If the location of the site is appropriate, ROADM sites and OTM sites composed of M40V/D40 back-to-back can all play the role of OEQ sites for pass-through wavelengths

A. FALSE

B. TRUE

正解：B 解答を投票する

出題：10

When which of the following pointers is adjusted, the information payload area carries the most information payload

A. No adjustment

B. Negative adjustment

C. All of the above are possible

D. Positive adjustment

正解：B 解答を投票する

出題：11

A certain system is configured with SOM, only the optical power information is in the query spectrum analysis data, and the OSNR is displayed as "---". The OSNR is abnormal at this time, the possible reason is ()?

A. Scanning spectra of OMCA/MCA4/MCA8 boards are inconsistent

B. Abnormal communication between network elements

C. The OMS segment is not correctly configured or the OMS segment is configured with a board not in place

D. There is a single-board optical cross-connection in the Och path or the Och is not created

E. After the networking changes, the SOM function is not reconfigured

正解：A,B,C,D,E 解答を投票する

出題：12

A network is configured with 1+1 protection on the board. On a certain day, the working channel has a condition that triggers protection switching, but the service cannot be automatically switched to the protection channel, resulting in service interruption.
The cause of the failure may be: (multiple choice)

A. Protection group configuration error

B. The configuration of the relay board between the source and sink is incorrect

C. There is an error in the protection channel

D. A lock switch or forced switch command is implemented

E. The optical fiber connection of the board is wrong

正解：A,B,D,E 解答を投票する

出題：13

In the network management planning process, which item is not completely necessary?

A. Network parameter planning and reliability planning of the network management server

B. DON network planning, OSS connection planning

C. Network management software/hardware configuration

D. Network scale planning, network management deployment planning

正解：B 解答を投票する

出題：14

SDH equipment mainly has two platforms, 4.0 and 5.0. In the main control board replacement, the replacement steps under different platforms are different. Which of the following operations are specific to the 5.0 platform?

A. Turn on smart features for smart nodes

B. Data from the network management

C. Software changes the network element IP

D. Software changes the NE ID

正解：A,D 解答を投票する

出題：15

The TN13FIU board does not support optical power detection, but supports reporting MUT_LOS alarms through alarm synthesis

A. FALSE

B. TRUE

正解：B 解答を投票する

H12-931-ENU試験無料問題集「Huawei Certified Internetwork Expert-Transmission 認定」